Pegasus AP1033 Installation Guide download pdf (Page 2)

CAUTION READ ALL INSTRUCTIONS CAREFULLY BEFORE

STARTING THE INSTALLATION!

Please handle all parts carefully to prevent scratches or breakage.

BEFORE YOU BEGIN

Thank you for purchasing the Pegasus

Kitchen Sink.

PLEASE READ ALL INSTALLATION

INSTRUCTIONS PRIOR TO

INSTALLATION OF THE SINK.

PLEASE ALSO READ AND

FOLLOW THE INSTALLATION

INSTRUCTION FOR ANY OTHER

PRODUCTS INTENDED TO BE

INSTALLED WITH THIS SINK.

CAUTION:

HANDLE WITH CARE

PLEASE NOTE THAT THE EDGE

OF THE SINK MAY BE SHARP.

TAKE ANY PRECAUTIONS

NECESSARY TO AVOID PHYSICAL

INJURY DURING HANDLING AND

INSTALLATION.

TOOLS AND MATERIALS

Ask your countertop dealer for a list of

the proper tools necessary to cut a hole

in the countertop.

Note: If a countertop is Corian, a

router must be used.

Read the installation instructions

that accompanied faucets and

accessories that are intended to

be installed with the sink. The

installation instructions likely will

provide a list of installation tools,

aids and tips for each individual

product.

To install this sink you may need:

An electric saber saw or router

A caulking gun with Acrylic or Silicone

caulk

A pencil

A tape measure

A hole saw 1 3/8”, carbide/diamond

tip recommended

An electric drill

A Phillips screwdriver

Scrap lumber (Two 2” x 4” each 2’

long would be sufficient)

A paint brush

Clean up materials such as

disposable cloths, soap and water.

RECOMMENDED TOOLS

Pencil

Electric Drill

with hole saw

(

pilot bit)

aulking gun

Phillips head

crewdriver

Electric saber saw

r router

BEFORE INSTALLATION

1. This sink was produced and

packaged by experienced people. Please

inspect your sink for any problems prior

to installation. If there are problems

that prevent installation of the sink,

please return it to the merchant from

whom the sink was purchased.

2. Determine from your faucet the

number of holes that your sink

requires in order to accommodate the

faucet. Faucets can require 1,2,3,4 or 5

holes. You may have already purchased

sink accessories to install on the sink

ledge. (Examples are a

soap/lotion dispenser, etc.) Add the

number of accessory holes required to

the number of holes required for faucet

installations, to determine the total

number of holes to drill into the sink.

Hole drilling to Faucet/Accessory Holes

and placement MUST

be performed

prior to installation.

DRILLING FAUCET/

ACCESSORY HOLES

READ THIS ENTIRE

SECTION BEFORE

STARTING TO DRILL.

Fig.2

the sink. (Do not use the countertop as

the structurally sound surface to

support the sink. Doing so will result in

damage to the countertop.

4. Scoring on the underside of the sink

is centred on the sink and indicates hole

positioning.

5. Drill straight down from the

underside of the sink, until the pilot bit

pierces through the sink surface.

DO allow the hole saw to cut completely

through the sink.

(Fig.2)

ink Bottom

INSTALLING YOUR

NEW SINK

1. See template for instruction steps.

TIPS FOR EASIER

INSTALLATION

1. After removing the countertop

cutout section is a good time to dry test

fit the sink in the hole, to assure that

the sink will install without any pitch

points. Test fit and remove sink, correct

hole if required.

2. Depending on the type of material

from which the counter is made, it may

be desirable to apply sealant to the raw

vertical edge of the cutout in the

countertop at this time. Silicone or

acrylic sealant may be spread with a

paint brush in a thin layer over this cut.

3. We have fount it to be easier to

install the faucet(s), accessories and

basket strainers to the sink at this point

rather than wait until the sink is

installed, (when all would be assembled

and installed from below the sink).

Follow the instructions from the

faucet(s), accessories and basket

strainers manufacturers to install the

product to the sink.

1. Drill holes from the Underside

of the sink.

2. Use a 1 3/8” Hole saw with

a pilot bit. (Fig. 1)

(Note: Use carbide/diamond

tipped for best results.)

3. Turn the sink upside down

being certain to not damage

the topside. Make sure the

sink ledge is supported by a structurally

sound surface. The two pieces of scrap

lumber mentioned in the Tools and

Materials section can be used to support

Fig.1

Hole Saw

P E G A S U S

K I T C H E N S I N K S

I N S TA L L AT I O N I N S T R U C T I O N S

English

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Pegasus AP1033 Installation Guide Page 2

Comments to this Manuals